decoration decoration decoration
decoration
leaf leaf leaf leaf leaf
decoration decoration

How to Use SVG Files with Scan N Cut

Learning how to use SVG files with Scan N Cut is important. Not all SVG files work well with Scan N Cut. In this tutorial you will learn how to make sure that your SVG file will work well with your Scan N Cut. ScanNCut SVG files need to be no larger than 11.75″ x 11.75″  using the standard sized mat, or 11.75″ x 23.75″ using the long mat. The DPI size also needs to be correct. Make sure that the ScanNCut SVG file has a minimum number of nodes. This tutorial will address all of these issues.

ScanNCut SVG

Scan N Cut

How was the SVG file Created?

SVG files may be created in any number of software programs. Some software allows the designer to add many different “pages” of file pieces on a single screen. This is fine if cutting from that software directly to a supported cutter. That software will allow you to select the specific portions of the designs to be cut in a given pass. SVG files of this type will work in many programs for many different cutters. However, any SVG file imported into the Brother Canvas Workspace software will be resized to fit the mat on the screen. When all pieces of the file are selected, and the width or length of the selection is greater than the screen mat size, the pieces will be resized to fit. So all of your design pieces may shrink to a very tiny size in the Brother Canvas Workspace or on the LED screen of your Scan N Cut.

FREE Rose SVG Cutting File

There  is a Free Large 3D Rose cutting file in SVG format in my Free Resource Library for you to use as you work through this tutorial. When it is cut and assembled, this rose has a width of about 7″.

ScanNCut SVG

Large 3D Rose SVG Project

The cutting pieces for this project measure over 17.5″ wide when selected in their original size. The largest petals measure 3.45″ wide.

ScannCut SVG

Original Size of Large Rose Cutting File – 17.5″ wide

But when you import this same design into Brother Canvas Workspace, you will receive a message that the design was resized to fit the Canvas Workspace.

ScanNCut SVG

Warning Message in Brother Canvas Workspace about Size

The resulting imported design in Brother Canvas Workspace was resized to be 11.75″ x 11.75″ and the largest petal measured 2.03″ wide. This size is about 58% smaller than the original. The final assembled flower would measure about 4.12″ wide. Now if this adjusted size is OK with you, then you can go ahead and cut the project to make the smaller rose.

ScanNCut SVG

Large Rose SVG file was resized in Canvas Workspace

Vendor Remedies for ScanNCut SVG Files

Some software vendors are aware of this issue, and save their larger SVG projects into multiple SVG files with a maximum width so that they will work with all software, including Scan N Cut. They will add all of the project SVG files to a single folder, and zip them up for a single download. You will need to unzip the folder once you have saved it to your computer, by clicking on the zipped folder, and selecting Extract All. Then you will be able to import one SVG file at a time to either Canvas Workspace or directly to your Scan N Cut via the Bluetooth connection, or via a thumb drive plugged in to the USB port on the machine.

How to Make Size Adjustments for ScanNCut SVG Files

If you have determined that you need to retain the sizing of the original file, how do you make the necessary size adjustments in the file so that it will work with the Scan N Cut? One option is to contact the original designer of the file, and ask them to limit the sizing of their SVG files to a width of 11.75″. However, that is not always practical for you or for the original designer. You can learn to make the necessary adjustments in the file so that it will work on your machine.

The best option is for you to use a third party software for making changes in your SVG file. Software that exports designs with the sizing of the original design are the free Inkscape ,  Make The Cut,  or Sure Cuts A Lot (using the 96 DPI export option or Save as FCM). SCAL is the best option for MAC users.

The Large 3D Rose file is a good place for you to start. Select one of the above software programs to use for editing your SVG files. Plan to stick with it for all of your editing needs. You will need to learn how to use it for many different purposes. Each has its own learning curve. See my video tutorial covering use of each of these three programs for making the small changes that this file needs.

How to Reduce the Number of Nodes for a ScanNCut SVG File

Whenever you change file formats for a cutting file, it is possible that extra nodes will be added to the design. If a design has too many nodes, or construction points, it may not load into Canvas Workspace or the Scan N Cut. It is therefore important to reduce the number of nodes in the design before exporting as SVG. In Make the Cut, you can use Ctrl+Shift + X to view path detail.

Reducing the Node Count in Make The Cut

ScanNCut SVG

View Path Detail in Make The Cut

In this file there are only a total of 434 points, and 182 Nodes, as indicated on the top line of the window. This number of nodes is not a problem for Scan N Cut. Some files with lots of tiny detail can have upwards of 30,000 nodes. That would be too many. To reduce the number of nodes in Make The Cut, select all (Ctrl+A), Join (Ctrl+J), Auto Simplify Paths (Ctrl+Shift+Z). The number of nodes will be significantly lower if there are too many nodes.

Reduce the Node Count in Inkscape

If you are using Inkscape, and your SVG file has too many nodes, select all (Ctrl+A) and Simplify (Ctrl+L) as many times as needed to get rid of excess nodes, a few at a time. This file does not need it. You only need to reduce nodes or simplify paths if you get an error when trying to load your SVG file into Canvas Workspace or into the Scan N Cut machine.

ScanNCut SVG

Warning when attempting to transfer a design with too many nodes to Scan N Cut.

Reduce the Node Count Using Sure Cuts A Lot

To reduce the number of nodes in a file if you are using Sure Cuts A Lot,  go to the Path menu at the top of the screen, and select Simplify. A window will open allowing you to see the nodes and reduce the number of nodes if there are too many. This design does not have too many nodes, so simplifying would actually add nodes as shown in the image below.

ScanNCut SVG

Use the Path Simplify tool to view the number and to reduce them if necessary.

Import your ScanNCut SVG Files into Scan N Cut Canvas Workspace or into the Machine

Once you have edited the SVG files to have its objects fit on a single design page in the software of your choice no wider than 11.75″,   reduced the number of nodes if necessary, and exported the files as SVG for FCM using the proper DPI settings, then you are ready to transfer your files to your Scan N Cut machine for cutting. You can copy the files to a thumb drive, and plug them in to the machine’s USB port, or import them into Canvas Workspace to Transfer to your Scan N Cut.

Cut the pieces for your ScanNCut SVG Large 3D Rose, and you are ready to assemble your flower.

ScanNCut SVG

Large 3D Rose SVG Cutting File

You can get the FREE cutting file for this project as well as additional SVG projects in my FREE Resource Library.

>> HOW TO ENTER THE FREE RESOURCE LIBRARY <<

This resource library is open to everyone for free. All you need is the password to get in, which you can get by filling out the form below.

If you already have your password, enter the resource library here.

Thanks!

Julie

cuttercrafter.com

Tips for Cutting Basswood on the Cricut Maker

Here are my tips to cut basswood on the Cricut Maker while making a lovely 3D Family Tree bursting with small magnolia flowers!

Cut Basswood

3D Basswood Tree decorated with names on hearts and 3D Magnolia Flowers.

Supplies Needed to Make the 3D Family Tree

Please note: Some affiliate links may be used in this post. I am affiliated only with products that I use. When you purchase products using my affiliate links, it does not cost you any more, but I will share some commission. Thanks!

One Basswood sheet 3/32″ x 8″ x 24″
Cricut Maker
Knife Blade holder and blade for Cricut Maker

Cricut Strong Grip Mat
Blue painters tape or masking tape
3D  Family Tree design by JenniferMaker.

Glue that dries quickly.
Heartfelt Creations 3D Rose Shaping mold 
Magnolia Flower Cutting File from the Free Resource Library
Cricut Printable Sticker Paper

Hot Glue Gun and glue sticks

 

Cricut recommends using basswood no thicker than 1/6″, but all I had was 3/32″ basswood. I used it to cut a lovely free 3D  Family Tree design by JenniferMaker.

Tips for Cutting Basswood on Cricut Maker

3D Basswood Tree

Preparation for Using the Knife Blade to Cut Basswood

First, If you have the Cricut Maker, order the Knife blade, and an extra blade. Basswood was hard for me to find locally. You may have to order some online. The other thing that would be good to order is the 2mm chipboard for the Maker. I noticed that this is an excellent quality chipboard. Not all chipboard is created equally. Some shreds easier than others, and cuts poorly. This chipboard is thick, firm, and a good cutting quality. It measures only 11″x11″ . Thicker media for cutting with the knife blade needs to be no wider than 11″.

After you receive your new knife blade, be sure to follow the instructions for its proper use. You need to calibrate the knife blade in the Cricut Maker machine. This process is easy  and quick. Then, move the white star wheels on the roller bar over to the right. I neglected to do this, and the wheels marked up the length of my wood. Do some small test cuts! See my post on how to make test cuts.

Cuts using the knife blade need to be no smaller than 3/4″, or about the width of a pencil. A few pieces of my 3D tree broke after removing them from the mat because they were on the thin side. Basswood is more sturdy than balsa wood, but it can split if you are not very careful handling it while removing it from the mat.

Use the heavy tack mat, and use painter’s tape or masking tape on the edges to keep the wood in place during cutting.

Cut Basswood with the Knife Blade

Heavy media takes many passes, and may take a very long time. Thick basswood required about 14-15 passes. The 3D tree took two hours to cut. There were two  large pieces to cut, and each piece took an hour. Stay near the machine during the cut, as the blade did get stuck about 4 times on each of the pieces. When the blade runs into tiny pieces of “dust”, cutting stops, allowing you to brush away the debris. You click on the C button to resume the cut at this point. No time is lost, and the machine does not miss any steps in the process. Since I was cutting media that was thicker than what was recommended, that may have been part of the reason for the blade getting stuck so much. But the cuts were still perfect!

You do have the option to add extra passes, one at a time, after the cutting is done, in case the wood is not cut all the way through. You simply press on the C button on the machine to have it cut again. Do not do this too many times, as the knife is capable of cutting all the way through the mat.

To remove the cut pieces from the mat, remove the tape first. Then roll the mat away from the wood. You don’t want to bend the wood, because it can crack and split.

Assemble the 3D Basswood Tree

You cut two pieces. One of them has a slit at the top, and the other has a slit at the bottom. Handling very carefully, slide the piece with the slit in the bottom as far as it will go over the other piece that has the slit at the top. The pieces will fit together very snugly if you are using Basswood with 3/32″ thickness. The cut pieces are fragile. The tree will stand on its own if the two pieces are aligned correctly.

Cleaning the Mat

Using a scraper tool on the mat after cutting wood is not a good idea. The bits of wood can get caught in the grooves of the cuts in the mat, ruining it. It is recommended that you wash the mat and use a brush with a circular motion to get the tiny wood pieces off of the mat. Then you can let the mat dry, or wipe it down with a soft cloth or paper towel. My mat cleaned up nicely. The knife blade did produce some pretty deep cuts on the mat, though.

Decorate Your Cut Basswood Tree

You may decorate your cut basswood tree according to your plan for its use. I decided to make my tree into a 3D Family tree, with names of family members printed on sticker paper, cut into heart shapes. To do this, you can print the names on Cricut Printable Sticker Paper, and use your electronic  cutter to cut around the printed names in the shape of hearts. Be careful not to cut through the backing sheet of the sticker paper. Performing a test cut on the sticker paper before proceeding is important.

Next,  adhere the heart stickers to the assembled tree. There are 72 small hearts onto which you may place stickers. Add  small  magnolia flowers on the tree branches. This is  a smaller version of the flower used on the lovely peony gift basket. Assembly of the small magnolia flowers is very similar to the peony flowers on the gift basket.

Instead of shaping the small flowers as a peonies with small beads in the centers, shape them as  more open Magnolia flowers. To do this, Instead of using the 3D Floral Basics  Shaping Mold from Heartfelt Creations, use their 3D Rose Shaping Mold. Use two petal layers and one leaf layer for each flower you wish to place on the tree. I used 32 flowers on my 3D tree, so I needed 72 petal layers. Use quick drying glue inside of one of the petals, and insert the other with petals alternating. Shape the leaf layer, add some glue to the center, and place the petal layers in the center of the leaf layer. Adhere the flowers to the tree branches so that they do not obscure any of the printing on the heart stickers,  using a dot of  hot glue on the back of each flower.

 

Cut Basswood

3D Basswood Tree decorated with names on hearts and 3D Magnolia Flowers.

 

You can use this lovely 3D Family Tree design as a nice table centerpiece, or decor for a special event. It can be a part of a 3D village, or it can be a special gift. For weddings you could have each guest sign a blank heart sticker, then you can place the stickers on the tree later. This idea would also work for baby showers or wedding showers. Another idea is to use this as a necklace organizer. Use colors and decorations to match the theme of your special event!

Get the FREE CUT FILES FOR THE Small Magnolia Flower 

You can get the SVG cut files for the Small Magnolia Flower as well as  some of my other FREE SVG projects from my FREE Resource Library.

 

>> HOW TO ENTER THE FREE RESOURCE LIBRARY <<

This resource library is open to everyone for free. All you need is the password to get in, which you can get by filling out the form below.

If you already have your password, enter the resource library here.

Love,

Julie, cuttercrafter.com

↼ Previous Page

- PAGE 2 OF 2 -

loading
×

>> HOW TO ENTER THE FREE RESOURCE LIBRARY <<

This resource library is open to everyone for free. All you need is the password to get in, which you can get by filling out the form below. If you already have your password, enter the resource library here. Forgot your password? I put the password at the bottom of nearly all of my emails. But if you can’t find one of my emails to you, you can either fill out the form above again or email me at hello@cuttercrafter.com Password Tip: I recommend you copy and paste the password in to avoid any accidental mistakes. If you ever forget your password, please email hello@cuttercrafter.com Not working? If you enter the password and the same page refreshes, without any contents, that means you put in the wrong password. Double-check your email, copy the password, and paste it in to the link above. Still not working? I promise the password works—I haven’t changed it since I opened the library.   Try the copy/paste method again and make sure the URL you are going to has https at the start of it (that’s a secure page and it makes a difference). If that still isn’t working, try a different web browser.
%d bloggers like this: