Make A Subscription Box Tower
Make a Subscription Box Tower from the boxes that you receive each month. Are you running out of room to store your subscription boxes on your shelves? Have you run out of room to add more book cases to your crafting area? Are you re-organizing your supplies so that they take up less space, and wondering what to do with the empty boxes? If you answer to these questions is “Yes!”, then making a subscription box tower may be just the project for you!
You are not alone, if you have struggles with wondering what to do with your one-to-two year pile of monthly subscription boxes. Some have unpacked the boxes, and reorganized their contents into file folders or zipper envelopes. But then, what do you do with the empty boxes? I hate to throw away the lovely boxes that could be re-purposed to store reorganized supplies, or other crafting supplies.
Supplies Needed to Make the Subscription Box Tower
Please note: Some affiliate links may be used in this post. I am affiliated only with products that I use. When you purchase products using my affiliate links, it does not cost you any more, but I will share some commission. Thanks!
Electronic Cutter (I used Pazzles Vue) Cricut Explore or Maker or Cameo 4 or Scan N Cut with Deep Cut Blade will work.
class=”content-box-red”>Red Line Tape
SVG Cutting File from our Free Resource Library</ class=”content-box-red”>9″ Square Subscription Boxes</ class=”content-box-red”>Free SVG cutting file from the FREE Resource Library
1/4 inch Satin Ribbon – about 7″ per box<
Double Sided Foam Tape
Jumbo Paper Clips – about 4 per box. Clips should be about 2 inches long.
Refolding Subscription Boxes to Make a Subscription Box Tower
I have a stack of 19 subscription boxes so far, from Crafter’s Companion. Instead of throwing my boxes away, I decided to refold my subscription boxes and make a subscription box tower. You can do the same by following these simple step-by-step instructions. There is no need to destroy the boxes if you simply refold them. Change them from top opening boxes to front opening boxes. This allows you to stack all of the boxes without having to unstack them to access their contents.
Get Started Refolding the Boxes
First, remove the box contents.
Next, unfold the side flaps of the box. To do this you will need to lift up and out on the side flap to slip the tabs out of their slots.
Repeat with the other side flap.
Pull the front flap down.
Now, fold the side flaps back down, inserting their tabs into their original slots.
Prepare the front flap to fold to the inside of the box. Use some strong double-sided tape to hold the side flaps down. Then fold the front flap to the inside of the box.
Fold the front flap to the Inside of the box. Press down firmly on the front flap so that the tape adheres well to the bottom of the box.
The front flap can now tuck back inside of the box to close it. When you make a subscription box tower, you will now be able to open the front flap to remove its contents. You will not have to move the other boxes stacked on top of it to access its contents.
Make Drawers for the Boxes to Make a Subscription Box Tower
Cut the Drawers
You can make a drawer to hold the contents of your box. The drawer will make it easier for you to access the supplies you keep inside of it. Make a drawer for each of your subscription boxes using the free template included in the Free Resource Library. Once you make a subscription box tower with front closing panels, your supplies will be easier to access.
8.25″ Drawer Template Pieces
Pieces included in the Template to Make a Subscription Box Tower Drawer
The Template for the Drawer includes files in several formats. If you will be cutting your drawer pieces using an electronic cutter such as Cricut, Scan N Cut, Silhouette, Pazzles, or Klic N Kut, you will be able to use the included SVG file. On the other hand, if you will be hand cutting the pieces, you may use the PDF template. The drawer measures 8.25″ square by 2.75″ tall.
Each drawer has three side panels, one front panel, two bottom pieces, and two panels for reinforcing the front panel. The red lines in the template represent lines that are to be scored. Cut each side panel from a single sheet of heavy cardstock measuring 8.5″x11″. If you are using the PDF file, you will use that part of the template four times. Notice that the front panel has a slit in the center to allow you to thread a ribbon through it.
Also, there are two pieces for the drawer bottom. One is for the inside of the box, and the other is for the outside of the box. There are two panels with slits in them included to reinforce the front edge of the box. One piece goes on the inside, and one goes on the outside.
Using an Electronic Cutter to cut Drawer Pieces to Make a Subscription Box Tower
The cutting files for this project are zipped together. Download the zipped file to your computer. Double click on the file you downloaded and select Extract All to unzip it. Open your cutter software.
Instructions for use in Cricut Design Space
Cricut Design Space users will upload the SVG file and click on Save. Then select the uploaded file, and click on Insert. Next, right click, and select Ungroup. Now you need to assign the fold lines to score. There are two score lines for each of the four side pieces. Select one from the panel on the right side of the screen. At the top of the screen, change the line type from Cut to Score. The lines will now appear to be dashed on the screen to indicate that these are score lines. Finally, select the shape and score lines, right click, and select Attach. Do this for each of the four side pieces. Select a front panel and its center horizontal cut line. Then right click and Attach. Now do this for each of the front panels.
Instructions for use with other Cutter Software
Scan N Cut users should use the FCM files. Notice that there are three files. The file names indicate how many times each file should be cut for a single box drawer. Load one file at a time into Brother Canvas Workspace. Select the pair of fold lines in each piece, and assign it to be scored. Score them, then cut.
Silhouette Studio users can use the SVG files. Import them into the Designer or Business edition of Silhouette Design Studio.
The SVG files can be used by all other cutter software. Score the red lines, and cut the black lines.
Get the FREE SVG Cutting File for the Drawers for the Subscription Box Tower
To get the free SVG Cutting file for the Drawers for the Subscription Box Tower, go to the resource library and enter the password. I have included the password at the bottom of most of my newsletter emails. If you have subscribed, check your most recent email to find the password. If you have not yet subscribed, I hope you will, so that you can be informed as I add more new projects to the Free resource library! Once you are in the Free Resource library, right click on the file name of the project. Next, select Save Link As or Save Target As.
Now, save the file to your computer. Next you will need to unzip the file. To do that, double click on the file you saved to your computer to open it. Then, click on Extract All. Now, open your cutter software, and import the SVG file. Select the pieces you wish to cut. Load your paper onto the cutting mat. Do a test cut to find the best settings for you machine, and cut the pieces you need. Repeat with the pieces you want to cut from a different color paper.
Assemble the Drawers
Make valley folds on the score lines. With the wide tab on the bottom right, place red line tape on the three edges of the upper flap. Turn this piece over, and apply red line tape to three edges of the wide tab.
Also add a strip of red line tape along the long bottom edge of the side piece as shown above.
Fold the wide flap along the score line towards the lower part of the box side to form a corner. Remove the tape liner. Now check to make sure the corner is perfectly square, and press down to secure the flap the side as shown above.
Prepare all four sides of the box in the same manner as the first. Now you are ready to put the pieces together. Remove the liner from the tape on the end of the box. With the narrow flaps on top, overlap the straight edge of the next side over the corner piece and press together.
Remove the tape liner from the flaps before adding another side. Now you are ready to add another side in the same way.
Adhere the final side of the drawer to complete the shape of a square box, pressing the corners firmly. Be sure to line the corner up squarely. Now remove all tape liner from bottom edge of the box. Square the corners, then press the bottom of the box over the flaps on the outside. Then turn the box over, and press from the inside.
Now you can add the other bottom piece on the inside of the box.
Remove the tape liners from the other side pieces. Fold these pieces to the inside and press firmly.
Finish the Front Panel
There are two additional panels for the front of the box. Glue one piece to the inside of the front, and glue the other to the outside of the box front. All front pieces have a slit. Cut a piece of ribbon about 7″ long, and fold it in half. Use a needle or pokie tool to push the folded edge of the ribbon from the inside of the box front to the outside. Then pull the ribbon through the slot about half way. Separate the inside flaps of the ribbon so that one piece goes up, and the other goes down. Tape or glue into place.
Slide the drawer into the front opening of one of the refolded subscription boxes. The ribbon will help you pull the drawer back out. Now you will be able to slide the flaps of the box into their original slots to close it up.
Add contents of your choice into the box, and close the side front panel.
Add Contents and Create Labels
Now, fill your drawers with whatever you want to store in them, then label the boxes. Then make an index for the box contents so you can find what you need. Also, if the boxes have important information on the sides or bottom that will be hidden once the boxes are stacked, take photos or scan the boxes. Print these on regular printer paper, and place inside the boxes or in a binder so that you can refer to them as needed.
Stack Your Boxes into a Tower
Your tower may be a single box wide, or double box wide, as you prefer. Use jumbo paper clips in the tab slots on the underside of the adjacent boxes to keep them together. To do this, unfold the paper clips. Then refold them with a wider curve at the top. One side of the clip will fit into a tab slot on one box. And the other side will fit into the tab slot on the box next to it. If the paper clips do not slide all the way in, you can use a small craft hammer to tap them into position. Also, you can use paper clips on the top side of the boxes if you like.
These boxes have paper clips on top and bottom to join the two boxes together.
You may apply adhesive to the box bottoms to keep them together. I have found that with the contents in the boxes, and having two clipped together side by side, the tower is stable.
Enjoy!
Julie, cuttercrafter.com
>> HOW TO ENTER THE FREE RESOURCE LIBRARY <<
This resource library is open to everyone for free. All you need is the password to get in, which you can get by filling out the form below.
If you already have your password, enter the resource library here.
Best Paper for Cutting
What is the Best Paper for cutting with your electronic cutter? The answer to this question depends on what you want to do with the cut paper. Are you wanting to cut very intricate designs? Are you wanting to make popup cards? Do you want to print on the paper before or after cutting? Are you cutting very thin paper or very thick paper? Do you need to emboss your paper? There are many factors to consider in your paper choices.

Best Paper for Cutting
There is some excellent general information about paper called The Ultimate Guide to Card Stock posted here. And there is excellent information about paper weights here.
No matter which paper you choose to cut, you must do test cuts. Test cuts help you determine the optimal settings on your machine. See this document for test cut suggestions.
Note: Some affiliate links may be used in this post. I am affiliated only with products that I use. When you purchase products using my affiliate links, it does not cost you any more, but I will share some commission. Thanks!
Machine Choice
Not every machine can cut every different type of paper well. For example the Cricut Maker can cut Tissue Paper, Construction Paper and Crepe Paper very well using its rotary cutting wheel.

Rotary Blade Kit for Cricut Maker
But other electronic machines may require special stiffening to be cut these thin papers. And most machines will not cut these very thin and very fragile papers at all.
Silhouette machines, such as the Silhouette Cameo can cut lightweight cardstock and text weight papers very well. But these machines are not rated to cut heavier cardstock or heavier media.
Is the Best Paper Made of Hardwood or Softwood?
Every paper mill has its own formula for creating paper. All use hardwood and softwood to make their papers. But the proportions of hard to soft woods used in the papermaking process varies. When you find paper that works extremely well for the projects you like to make, take note of the mill that produces that paper. You might want to consider purchasing your favorite papers in quantities. When you get some papers that do not cut well for the projects you like to make, avoid purchasing papers from the mills that produce them.
For example, I purchase inexpensive paper made by Georgia Pacific for test cutting new designs if they are not too intricate. But when making final project cuts and intricate designs, I prefer to use papers by Neenah or Colormates from Worldwin. These papers seem to be crispier, and cut without shredding. Even very intricate designs cut very cleanly on these papers. Crispy papers have a higher hardwood content that make them cut better on electronic cutting machines.
However, stiff and crispy papers may crack under pressure when using Die Cutter/Embossing machines. In this case, it is important to test small samples for embossing, before you purchase in bulk. You may find that paper that cuts best on the electronic cutter, is not the best paper for using in a pressure embossing machine.
The Best Paper for Light Weight Projects
Tissue Paper
When you want to emboss many, many layers of tissue paper, embossing folders used with Die Cutter/Embossing machines work great. However, tissue paper may rip and tear under a cutting blade in a cutting machine. For this reason, a rotary blade, such as that available for use on the Cricut Maker works best. You can cut some amazing flower petals from tissue paper using the Cricut Maker and rotary blade.

Cricut Maker
Use a light tack mat, or the project may tear when you remove it from the mat. Do not attempt to cut any shape smaller than 3/4″ using the rotary blade. Cut larger simple shapes from tissue paper for best results.
If you are needing straight cuts, a hand-held rotary tool may work for cutting multiple layers at a time. Then you can use scissors to make any necessary curved cuts.
Crepe Paper
Crepe paper comes in a wide variety a weights and attributes. When making crepe paper flowers, getting a quality crepe paper that stretches nicely is important. Crepe paper comes in many weights. You may be able to cut heavy crepe paper, ironed between two layers of freezer paper with a regular blade on your electronic cutter. But I have found that if I want to cut crepe paper on a cutter, Cricut Maker using the Rotary blade is the only machine that will do it well without tearing. Again, do not plan to cut any shapes smaller than 3/4″.
Crepe paper rolls for decorating may not be your best choice for cutting. This type of crepe paper is very thin, and stretches very little.
Construction Paper
Construction paper is very inexpensive. But it is also tears very easily. Its fibers are very loose. Cutting blades rip and tear in the cutting process unless using a rotary cutting blade. Use the rotary blade on the Cricut Maker for simple cuts on construction paper. Otherwise, scissors may cut the best. Construction paper is not always the Best Paper option for use with cutters.
Vellum
Translucent vellum used for crafting is generally a thin, but crispy paper that cuts well with a blade on electronic cutters. It comes in a text weight or as cardstock. The text weight paper is very fragile, so should be handled carefully. Translucent vellum cardstock works extremely well with line embossing on electronic cutters. And it cuts very well, too, without using a special backing or freezer paper.
You can create some lovely parchment type crafts using vellum, an embossing tool, piercing tool and cutting blade on your electronic cutter. If your machine does not have piercing and embossing tools available, it is possible to use hand embossing or piercing tools in a pen holder. The tip of a blade can produce a pierced effect if you don’t have a piercing tool.

Pierced, embossed, and cut Vellum popup butterfly
Scrapbook Paper
Decorative scrapbook papers are fun to use on cards and scrapbook layouts. Most cutters can cut scrapbook paper without a problem. But some scrapbook papers cut better than others. Some scrapbook papers made of layers may split, bunch or tear when cut. If you have papers that give you problems, avoid tiny cuts. Use them for cutting larger shapes. Cutting small welded text with sharp angles can result in lots of tearing. It is better to use nice crispy paper without a white core for intricate cuts and tiny text. If you find a brand that cuts well, stick with that brand for cutting with your machine.
Text Weight Paper
Paper that feeds into printers is usually text weight. 20# text is very light weight printer paper. 24# paper is better than 20# for double sided printing. 37# text weight paper is very nice for print and cut projects that do not need to be stiff. You can use shimmer papers for making lovely 3D flowers. This paper is described as 18 GSM (32/80lb Text) , The key word is “text” – this is NOT cardstock. It feels like quality letterhead paper. It has a smooth, Satiny Metallic finish.
Text Weight Papers can also be sold in heavier weights. Even up to weights that are nearly equivalent to medium weight cardstock. Be sure to read the weight specifications. Is it Text Weight or cover stock? Even more importantly, try some test cuts. Does it cut well for your purposes? If you need to print on it, will it feed through your printer smoothly? It is recommended for use in printers? Heavy cardstock may not work well for cutting around printed images.
Be sure to use a light tack mat when cutting light weight papers. Light weight papers may not come off of a brand new, very sticky mat. At least you should condition a new mat, and do test cuts on heavier paper on a new mat before using it with lightweight paper.
Best Paper for Cardstock Projects
Cardstock is available in weights from medium weight 65# up to very heavy weight 110#. 70#, 80#, 90#, 100# and 105# are also common cardstock weights. You may want to have a variety of weights on hand for different projects.
Medium Weight Cardstock
65# cardstock is the most common medium weight cardstock. It can be used for cards, scrapbook photo mats, stamping embellishments, home decor, gifts and other crafting projects. Some medium weight cardstock cuts well, and others do not cut well on electronic cutters. If you have some medium weight cardstock that does not cut well on your electronic cutter, try using it for embossing on cards and embellishments. It may also be used for making simple shapes or photo mats.
It is easy to assume that your cutter is broken when nothing will cut right. However, “mushy” paper is the culprit for bad cuts more often than not for me. Also, be sure to check the cutter maintenance tips to rule out other causes of poor cuts.

Cuts before and after cutter maintenance
Heavy Cardstock
Any cardstock above 80# is considered to be heavy weight. 100# cardstock is great for coloring, molding, and shaping for 3D flowers. You will love 110# cardstock for creating heavy duty boxes and 3D paper projects. 100# cardstock is great for making popup cards. You will like using 80#-90# cardstock for making cards, intricate frames, borders, corners, etc . If you prefer cutting heavy cardstock, stay away from the cutters that are limited to cutting medium weight cardstock.
Some heavy cardstocks have polyester fibers in them, which make them strong. But these polyester fibers make them much more difficult to cut cleanly, especially on intricate designs. The polyester fibers also are very hard on blades, dulling them quickly. These textured papers make very nice cards and photo mats. However, they may not be the Best Paper for cutting with your electronic cutter.
Watercolor Paper
Watercolor paper can have different weights and densities. These papers are great for watercolor projects. Cutting watercolor paper into simple shapes may not be problematic. But it might be best to cut only simple, basic shapes from it. Because watercolor paper is not crispy, it may tend to bunch and shred by the blade. You may be able to cut shapes around your watercolor designs if you are careful.
Matboard
Professional quality photo mats are made from 4-ply matboard . Matboard is very stiff, and very difficult for most electronic craft cutters to handle. Some of the cutters that can cut with up to 1000 grams or more of pressure can cut 2-ply matboard up to 2mm thick. The cutting blade must also be able to handle the thickness of the Matboard. Some cutters, such as Scan N Cut, have the pressure rating for cutting heavier materials. But they are limited in the thickness that they can handle. Scan N Cut 2 is rated to cut media no thicker than 1.5mm. Read more about cutting matboard with the Knife Blade on the Cricut Maker here. Pazzles Vue can cut 2 ply matboard up to 2mm thick.
Scan N Cut 2 cuts media only up to 1.5mm thick. The Scan N Cut DX to be released in the Fall of 2018 is boasting a 3mm thickness cutting option. Cricut Maker cuts media up to 2.5mm thick, but would require the optional Knife blade to access the pressure needed for cutting thicker media. Pazzles Vue cuts media up to 2mm thick. Some of the KNK machines will cut Matboard, as does the Silver Bullet line of cutters. Be sure to check your cutter specifications before investing in Matboard to cut.
Chipboard
Chipboard comes in many thicknesses and densities. Some chipboard is made of multiple layers. Some is coated on a single side, while others have a coating on both sides. Most cutters can handle cutting cereal boxes, which is flexible chipboard. Some chipboard is not flexible. That type is most difficult to cut. Some chipboard shreds during multiple cutting passes. There is chipboard available that cuts well without shredding. Here is an excellent article about chipboard. Cricut sells 11″x11″ chipboard made specifically for use with the Cricut Maker. Silhouette sells a chipboard colored cardstock, as regular chipboard cannot be cut on Silhouette machines.
I prefer cutting chipboard that will cut in a single pass. This is because the density of chipboard can cause a cutter to skip steps. If this happens, successive passes would not be in exactly the same location as previous passes. This results in shredding of the chipboard and very poor cuts. If multiple passes are necessary, it is best to start with lower blade extension and cutting pressure, then increase these settings for the next passes. This reduces the possibility of missed cutting steps. If you need thicker chipboard pieces, you might want to try cutting several pieces of .022″ chipboard, and gluing them together to make your project. Do not plan to cut intricate designs from chipboard.
Cricut Maker users may cut chipboard up to 2mm thick with the optional knife blade. The interesting thing about using the chipboard setting in Cricut Design Space, is that chipboard and other thicker, denser materials do not use a cutting pressure any more than 750 grams. The secret to success for this machine is the slow cutting, and many, many passes. The blade needs to have sufficient cutting surface to cut completely through the thickness of the chipboard.
Best Paper Brands for Cutting
I have been using electronic cutting machines since 2004. The brand of paper that I have had consistently excellent cutting results with is Worldwin Papers, I have used most of their papers varying from very light weight to very heavy weight, and all of them cut with excellence on my cutters. Their textured 65# Cutmates line is guaranteed to cut well on any electronic cutter. The selection of colors in the smooth 65# Colormates makes it to be much in demand among cutter users. My personal favorite smooth paper by Worldwin is the 90# Colormates Smooth and Silky. Their colormates line of heavy textured cardstock is also wonderful to cut. I love their metallics as well.
If you cannot find the Worldwin papers you need at Amazon, you can purchase your favorites from The Paper Mill Store.
When I need low cost paper options that I can get quickly locally from Michaels, I purchase Recollections cardstock . Their 65# cardstock generally cuts well, as does their very heavy 110# cardstock.
Paper Brands to Avoid
I avoid papers from Joann. Their Core dinations brand does not always cut well. I save this paper for purposes other than cutting on my electronic cutters. Paper sold at Walmart is inconsistent for cutting purposes. One color in a package may cut OK, while then next color will not cut well at all. These may work for simple shapes, but I stay away from their papers when cutting intricate projects.
Best Paper Hints and Tips
Humidity
Nice paper for cutting may not cut nicely if it has been exposed to humidity. Pressure and blade settings may change with the environment. What cut well this morning may not cut so well at the same settings in the afternoon when the air conditioning is running. Always do test cuts when environmental changes occur.
Storage
Store your paper in Zip lock bags after you have opened its original packaging. Two-gallon zipper bags fit 12″x 12″ papers well for storage. Storing them this way will prevent the papers from collecting excess moisture that can hinder cutting quality. Moist papers get “Mushy” and may tear and bunch during cutting.
Emboss the Cut
If you have some paper that is not cutting well, try using an embossing tool or scoring tool in the machine over all of the cut lines a couple of times at very high pressure. Then cut as you normally would. The embossing tool compresses the paper along the cutting lines so that you can get much better cuts.
Drying with Heat
Some have mentioned drying paper that has soaked up moisture in the oven. If you attempt this trick, be sure to keep an eye on the paper, so that it does start burning. Using a low temperature in a dehydrator for a longer period of time might be safer. Check on the paper at regular intervals. Some prefer to dry out paper using an iron.
Chipboard
After removing chipboard from its packaging, it gets thicker overnight. New chipboard straight from the packaging requires different settings than would be required if the paper sits out overnight. Cricut recommends letting its chipboard sit out of the package for a day before cutting for best results. Chipboard is very absorbent, and sensitive to environmental conditions.
Be sure to use a high tack mat and possibly tape the edges of chipboard and other heavy media to the mat to keep it from moving around during cutting .
Best Paper Cutting Settings
Because paper is very environmentally sensitive, the same paper may require very different settings. Those who live in very dry climates will need to use less cutting pressure than those who live in humid environments. For this reason, performing your own test cuts is extremely important. Don’t rely on a published list of settings or presets. Sometimes different colors of paper in the same package can require different settings. What cut well yesterday at certain settings may require different settings today. Be sure to do test cuts at the beginning of each cutting session, and any time you make color changes or environment changes.
Best Paper Conclusion
If you are faithful to do test cuts, you will be more successful cutting any papers you have in your collection. Be sure to keep lots of inexpensive paper that cuts well, on hand for doing project test cuts. Save your expensive paper for the final versions. This will save you lots of frustration.
The paper that is best for you depends on what you like to cut most, and what machine you have. Special tools available for use with your cutter can also make a difference in how they cut.
Here is FREE cutting project that you can use to check how well your paper cuts with each of the tree layers. The hearts layer provides some intricate cutting, while the white layer provides a simple shape to cut. The Brown layer has some intricate inner detail. You can use this project on a card or scrapbook layout.

Love Football Border
>> HOW TO ENTER THE FREE RESOURCE LIBRARY <<
This resource library is open to everyone for free. All you need is the password to get in, which you can get by filling out the form below.
If you already have your password, enter the resource library here.
Love,
Julie, cuttercrafter.com
Pazzles Inspiration Vue Cutter Review
Pazzles Inspiration Vue may be the electronic cutter you need. It ranks among the top electronic cutters. The Vue is a powerful, but simple to use machine. You can cut many different types of materials with it. And with optional accessories, you can also use the Pazzles Inspiration Vue to cut, draw, engrave, emboss, pierce, and distress many media types. The Pazzles Inspiration Vue is the choice of beginner and well as professional crafters. This article reviews the features of this amazing machine to help you decide if this is a good choice for your crafting needs.
Note: I may have used some affiliate links in this review. I am affiliated only with products that I use. When you purchase products using my affiliate links, it does not cost you any more, and the tiny commission that I get contributes towards the costs for maintaining my blog. Thanks for your support!
What Do You Want to Cut?
Cutting Vinyl with the Pazzles Inspiration Vue
The Pazzles Inspiration Vue cuts vinyl of all types, whether the vinyl is repositionable wall vinyl, permanent outdoor vinyl, heat transfer vinyl, vinyl window cling, Stencil Vinyl, Glitter or Flocked vinyl or other types. It is recommended that you cut your vinyl on either the 12″ mat or the 24″ mat. Reserving a standard cutting blade for cutting vinyl ensures that you will always get smooth cuts with for your vinyl projects.

Split Regal Monogram on a Ceramic Tile
You can make wonderful gift items such as the customized tile above using your Pazzles Inspiration Vue electronic cutter. The design for the shirt below was a special request from my husband. The Pazzles InVue software that ships with the machine, allowed me to create the cutting design from an actual photo of my husband fishing.
Cutting Heavy Cardstock with the Pazzles Inspiration Vue
Entry level cutters do not have sufficient cutting pressure to allow users to cut heavy media. The Pazzles Inspiration Vue boasts of up to 1000 grams of down pressure, making it rank among the top home crafting cutters. It can cut media that is up to 2mm thick. So it can cut even tough chipboard. If you love to cut 3D projects from heavier media, you will need a more powerful machine. This machine boasts of three times the cutting pressure of the legacy Cricut machines as well as the Cricut Explore models. And it has about 4 times the cutting pressure of Silhouette and Craft Robo machines. The print and cut embellishments used on this card were all created using the Pazzles Inspiration Vue and its InVue software.
3D boxes such as the Trailer Gift Box below are much more stable when cut from heavy cardstock.
Here is another project that required heavy cardstock. If you love making sturdy 3D projects, you will be happy if you have a cutter that can handle cutting the required heavy media.
Projects like this Snow Globe Box Card last a lot longer on display when its pieces are cut from heavier cardstock. Pazzles Inspiration Vue cuts these so efficiently! The intricate snowflake detail cut beautifully on this machine.
Engraving Metal with the Pazzles Inspiration Vue
You can use Pazzles optional Diamond Tip engraving tool to engrave on metal. I recently engraved on a dog tag for our puppy. The tallest letter was .057″ and the smallest letter was .06″ tall. The entire tag was only 1.5″ wide. I was able to fit four rows of text on the back of the tag with our puppy’s name, address and phone number. Here is the front of the tag. (I blurred the phone number.) You can cut thin aluminum metal with the blade.
Cutting and Piercing Delicate Designs in Vellum with the Pazzles Inspiration Vue
You can also cut very fine and delicate media such as vellum. I used Pazzles optional Piercing and Embossing tools on vellum to create this popup butterfly anniversary card.
Cutting Fabric with the Pazzles Inspiration Vue
Cutting fabric with this machine is great. I was amazed at how nicely my Vue cut the doily and the flowers out of fabric for this Easter Bonnet. It is good to reserve a blade dedicated to cutting fabric, since paper can dull blades quite quickly.
Cutting Wood with the Pazzles Inspiration Vue
Yes! This machine cuts thin balsa wood or basswood up to 2mm thick. Here is a Captain’s Wheel design that I cut. Covering the back of the piece of wood with blue painter’s tape before cutting keeps the thin wood from splitting during the cut and while lifting from a very sticky mat.

Captain’s Wheel cut from thin wood, with pen writing.
Making 3D Flowers with the Pazzles Inspiration Vue
If you love making 3D paper flowers as I do, you will be happy to know that this machine cuts lots of different types of paper petals for making beautiful flowers. This bouquet includes some vellum flowers, some made from printed scrapbook paper, some from medium weight cardstock, and some from heavy cardstock.
Cutting Rubber Stamps
You can create your own custom rubber stamp designs using the Pazzles InVue software that ships with the Pazzles inspiration Vue. Then you can cut the rubber using the Pazzles Inspiration Vue. I had an idea for a musical stamp, so I created the design, and let my Pazzles Inspiration Vue machine cut it out for me.
Cutting Clay, Fondant, Gum Paste and Frosting Papers using the Pazzles Inspiration Vue
You can use Pazzles optional Cake Accessories Kit for cutting clay, fondant, gum paste, and frosting papers. Here is a project I made using thinly rolled Sculpey clay.
Cutting Scrapbook Page Overlays
Scrapbook pages are fun to make using the Pazzles InVue software and cutting with Pazzles Inspiration Vue. This machine will cut a full 12″ wide border or scrapbook page. It is not limited to an 11.5″ cutting width as some cutters are. Here is a scrapbook calendar page that I created. Notice the detail of the embellishments.
Rhinestone Templates
Designing templates for use with rhinestone designs can be done using the Pazzles InVue software that ships with the Pazzles Inspiration Vue cutter. You can turn any design or test into a rhinestone template design. Then you can cut your template out of rubber designed for cutting rhinestone templates using your Vue. Here is my first rhinestone project.
Cutting Around Printed Images
Before I received my Pazzles Inspiration Vue, I was never happy with the cutting around printed images with my other machines. You will love how the Pazzles Inspiration Vue automatically finds the registration marks, and cuts perfectly around printed images that are up to 8.5″ wide. This project would have been extremely difficult to cut and assemble if I had cut each tiny element separately. Instead, I chose a number of appropriate designs from the generous Image library available in the Pazzles Craft Room, and printed the shapes. Then I had my Vue cut around the printed images. It did a great job!
You can see more of my Pazzles creations here .
What is your Cutting Skill Level?
If you are a novice cutter user, you will appreciate how easy the Pazzles Inspiration Vue cutter is to learn to use. With the great support offered by Pazzles to its customers through the Pazzles Craft Room, you can learn to start using your Vue to make amazing projects right away. The Pazzles Craft Room has hundreds of projects like the above, ready for you to download, cut, and assemble. The downloaded projects are yours to keep, even after your membership expires. And their Angel policy allows you to use the designs commercially. You can get almost all of the above projects for free as a member of the Pazzles Craft Room.
Ease of Use
The click style blade holder in the Pazzles Inspiration Vue makes setting blade depths easy. The software tells you where to set the blade for the media type that you have selected to cut. The blade holder and blade are the same ones that the Deep Cut blade holder and blades that legacy Cricut machines used. The blades are easy to insert and remove.
The machine automatically loads your mat. The optical reader sets the starting point at the same place every time. The optical reader also makes cutting around printed images so much easier!
More Advanced Users
You will love the flexibility you have in using the Pazzles InVue software. It has all of the basic functions with which you are familiar from other cutting software. But it also has lots of advanced design and editing functions. Some of these advanced features are not available even in the most expensive professional design software programs. Pazzles developed their InVue software with all the advanced design features that its staff and professional users were familiar with, and used to using.
The amazing thing about this software is that it is provided for FREE with the purchase the the Pazzles Inspiration Vue. And it is available for a VERY low price for those who wish to purchase it separately and use as third party software with other cutters. This software, combined with the advanced cutting technology in the machines, means that you most likely will not outgrow its functioning for your crafting purposes.
What is your Price Point?
Some people like to start their cutting adventure with a very inexpensive machine. Then they start saving their money, and plan to purchase a better machine when they outgrow the features of that machine. Others prefer to get the best machine they can get, so that they won’t be outgrowing its features any time soon. Pazzles Inspiration Vue is one of those machines that meets your growing cutting needs, without a need to upgrade to bigger and better machines later on.
Purchase options
There are several shopping options, making your purchase of the Pazzles Inspiration Vue cutter affordable. You can check out those options here. If you wish to purchase the machine outright, you will get the best price by first joining the Pazzles Craft Room for one month. While a member, you will receive a 15% discount on all Pazzles purchases. So you can get a 15% discount on your machine, and all the optional accessories you need. I save on shipping by purchasing all that I think I might need for a year. I like to keep three good mats and three extra blades on hand at all times.
With your outright purchase, you will receive several months of free membership in the Pazzles Craft Room. Be sure to take advantage of that time to view all of the training videos in the video library. These will help you get a great start in using your new machine. Also, be sure to download all of the cutting files and projects that you can get while you are a member. You can download up to 400 files per month, if you are diligent to download 40 files every 70 hours. These are yours to keep. While you are a Pazzles Craft Room Member, all downloads are FREE!
If you find that you love all the new projects that are regularly posted, you may decide that you want to maintain your Pazzles Craft Room membership. I really like all of the wonderful projects that they offer so much that I decided to keep my membership going. The best price for me turned out to be purchasing a machine for $99 with a two year commitment to the Pazzles Craft Room. Another similar option is to purchase a machine for $199 with a one year commitment to the Pazzles Craft Room.
System Requirements
Pazzles Inspiration Vue works on both Windows 7, 8, and 10, and on Mac: OS X 10.9.X & 10.10.X.. It needs a USB2 connection directly to your computer. The InVue software also works on these machines. You will need software to cut to the Vue. You can use Pazzles InVue software or you may use Sure Cuts A Lot. If you have Pazzles Inspiration Studio Pro 1014, you can use it to cut to the Vue. However, that software is no longer available for sale.
You do Not need high speed internet in order to use your Pazzles Inspiration Vue. Connect to the Internet to update your firmware and software one time after receiving your Vue. You can disconnect your Vue from your computer after making a cut. Then you can repeat that exact same cut with the same settings as many times as you like by pressing the Repeat button on the machine. When you need to make a lot of the same project, this is a real handy feature to have.
Pazzles Inspiration Vue Specifications
This cutter ships with the machine, USB cable, power cord, and converter box, blade, blade holder, and a print and cut mat. The machine will cut up to 1000 grams of pressure using settings of 1-50. You have 5 speeds from which to choose. The click blade holder has 11 different blade depth settings. Maximum cutting width is 12″. Cutting length is 12″ with the standard mat, and 24″ with the 24″ mat. The machine weighs 11.2 pounds, is 22″ wide x 6.5″ tall x 11″ deep. Its roller bar has two permanent pressure rollers, and four more rollers that are removable when cutting thicker media.
There is an accessory tray on top of the machine as well as three slots for additional tools. A support tray for the mat is built in to the front of the machine. You slide it out when using the machine. Then push it in when done.
Pazzles InVue Software Overvue

Pazzles InVue Software
The InVue software ships without additional cost to you with your purchase of the machine. It has many outstanding features. For that reason, we will touch only on the highlights. The software has special features not only for cutting, but also for drawing, piercing, embossing, engraving, distressing, and converting to rhinestone designs. My favorite tools are the replace with a line, and replace with an arc.
The software will import and export SVG files. It will also import and export WPC files. The image gallery connects to your online account with Pazzles. This allows you to download all new files easily. The software automatically stores these downloaded files in the correct topical file folders on your computer. Downloading files from the online library requires an Internet connection. But once they are saved to your computer, no internet connection is necessary for using them.
Software Pros
There are a variety of welding options in the software. One that is unusual to see is the WYSIWYG weld function. This allows you to arrange design pieces as you wish to see them. Then you use WYSIWYG Weld to get rid of all overlapping lines instantly. It has a nice inline/outline feature. It also has a nice Duplicate feature that lets you fill your page with the selected images.
The software will also convert images to cutting lines. There is a nice Fit text to path feature, which allows you to select any path for the text to follow. I love the Vertical/Horizontal tool, and the corner rounder features as well.
Text
The software will access any fonts installed in your computer’s system fonts folder. It will also access single stroke fonts that you have installed. The software has a very nice text preview window. This allows you to type in text and preview how it looks with any of your installed fonts. I love being able to see the text in different fonts in a large size before I select one. Once you have added your text to the layout, you have many options for spacing and kerning. Thickening fonts is easy in this software. Creating mats for text is also easy. So you can make some lovely word art quickly and easily with this software.
Software Cons
Features that I miss in the Pazzles InVue software are freehand draw, fit object to path, and blackout shape. I miss the scissors cuts we had in Inspiration Studio Pro 2010, and the Create a Font option. This software is missing the word envelopes, simplify paths, and smooth small angle tools.
I go back to Make The Cut to use its better tracing options, its Conical Warp, and Texture Snapshot features. The MTC measuring tool and Lattice functions are some tools that I miss as well. Thin paths, Fuse and Weld and the Tiler functions are also features that I still go back to Make The Cut to use.
I go to Sure Cuts A Lot to make instant Knockout Text. We can do this using InVue software, but it takes a few more steps. Viewing and using alternate glyphs in the private use area of fonts is another feature of Sure Cuts A Lot that I use on occasion. I go to CorelDraw to use the envelope for fitting text to a shape and for creating True Type fonts. CorelDraw and Illustrator have useful batch conversion utilities that come in handy from time to time. Sure Cuts A Lot does a batch convert for Brother FCM files. Pazzles InVue software does not have any batch conversion features.
The nice thing about the Pazzles InVue software is that even if you go to other software to use certain features, you simply export the files as SVG, import into InVue, and you are ready to cut. You get the best of all of the software choices this way.
Conclusion
Now you have an idea of some of the great things that the Pazzles Inspiration Vue can do for you. You need to figure out what your specific needs are. I have 14 different cutters in my collection. Each one has its own special purpose. I select the one that will work the best for the project on which I am working . You need to determine if the Pazzles Inspiration Vue or another machine meets those needs better. Study your options. What do you like to do the most? Get the best machine that you are able to afford that will work the best for your purposes. So the most important thing is for you to use what you have until you can get something better. You won’t really know exactly what you need until you start using what you have!
Free Thankful For You Tag SVG Cutting File
I have created a new cutting file for you using my Pazzles InVue Software, and I cut it on my Pazzles Inspiration Vue cutter. But you can use the FREE SVG cutting file with your own software and cutter. You can get the FREE Thankful For You Tag SVG cutting file in my FREE Resource Library. See the link at the bottom of the page.

Thankful For You Tag
>> HOW TO ENTER THE FREE RESOURCE LIBRARY <<
This resource library is open to everyone for free. All you need is the password to get in, which you can get by filling out the form below.
If you already have your password, enter the resource library here.
Love,
Julie, cuttercrafter.com
Easy DIY Tool Organizer
You can make an Easy DIY Tool Organizer to keep your most used tools for cutter crafting handy on your desk next to your cutter. This is a great first project to try after you have set up your cutter and finished performing some test cuts.

Easy-DIY-Tool-Organizer
You will find the cutting files for this project in the Free Resource Library. There is also a special file in the Free Resource Library with a list of Five Must-Have Cutter Crafting Tools which you likely have around your home already. This Easy DIY Tool Organizer will provide a place to keep these important tools so that they don’t get lost, and they remain handy while you cut and craft!
Supplies Needed to Make the Easy DIY Tool Organizer
Two sheets of heavy 12″x12″ cardstock
Glue that dries quickly.
Cutting File from the Free Resource Library
Five Must-Have Cutter Crafting Tools
Assembly Instructions for the Easy DIY Tool Organizer
To make this Easy DIY Tool Organizer, use the heaviest cardstock that you have that your cutter can cut. Be sure to do a test cut to determine the best pressure and blade extension for the cardstock that you have chosen. Since the cardstock is heavy, it is important that you use a brayer or other similar implement to press the cardstock firmly on the cutting mat. Heavy pressures can cause the paper to move around the cutting mat during cutting if the cutting mat is not sticky enough.

Adhere cardstock firmly to the cutting mat.
Cutting the Easy DIY Tool Organizer
Download the zipped cutting file from the Free Resource Library and Extract All. Open your cutting software and import the appropriate file. Most cutter software can use the SVG file, but there are other formats included for those who need them. Follow the instructions for using SVG files with your cutter. If you are using Cricut Design Space, see How to Use SVG Files in Cricut Design Space. If you are using Scan N Cut, open the FCM files. There are two files for Scan n Cut users. See also How to Use SVG Files with Scan N Cut. Open the MTC file to cut the design from Make The Cut. Or see this video tutorial on how to find and use SVG files with Make The Cut. Open the PVGC file to use with Pazzles InVue software. If you are using a Silhouette or Cameo machine, open the Studio2 file. If you are using Sure Cuts A Lot, open the SCAL4 file.
Once you have the file open in your software, send it to cut. There are two design sections, represented by two different line and fill colors. Select one portion of the design and cut. Remove the cut pieces for that cut. This piece may require a 24″ long mat. However, if you place your 12″x12″ paper strategically on your cutting mat, you may get it all to cut on the standard cutting mat.

Cutting file part 1 pieces.
Now you are ready to cut the pieces for the second part of the Easy DIY Tool Organizer.

Second part of the box.
Fold and Glue First Box
Fold on all of the score lines using mountain folds, folding towards the back of the pieces, for the first part of the Easy DIY Tool Organizer.

Fold towards the back on all score lines on this piece.
Put glue on the outside of each of the glue tabs for the main box. Fold up the side pieces, and hold the tabs in place until the glue is dry to form a box.

Glue the tabs to the end pieces of the box
Add glue to the outsides of the tabs on the dividers, and place inside of the box, about 3/4″ from the ends of the box, or wherever you wish to place them to fit your tools.

Glue the dividers inside of the box.
Fold and Glue Second Box
Fold on all of the score lines using mountain folds, folding towards the back of the main box piece. The long narrow strip has folds that alternate between mountain and valley folds, as shown in this photo. From left to right the folds are as follows: valley, mountain, mountain, valley, valley, mountain. The partitions on the left side of this box are larger than those on the right.

Fold tabs for Box 2 as shown.
Glue the tabs on the main box piece to the end pieces. Hold in position until the glue is dry, forming a box.

Glue the second box together.
For the inside partition piece of this box, place glue on the two flat sections where they will line up against the front and back of the box. The small tabs need glue as well, where they attach to the main box. Make sure you have the narrower compartments on the right side. Place the right side into the box, lining up the tab with the front right corner of the box. Make sure the the sides of the compartments are straight. Then hold in position until the glue is dry.

Partitions inside of the second box.
Assemble the Easy DIY Tool Organizer
You may use the two boxes separately, one on either side of your cutter. I like to use strong double stick tape to adhere the boxes securely to the cutter end caps.

Use a box on either end of your cutter if you like.
But my current setup makes it easier to access my important cutting tools by having them both on one side of my cutter. To make the two boxes into a single unit, glue the back of the smaller box to the front of the taller box. Be sure to line up the bottoms of both boxes against your desktop.

Glue the two boxes together to make a single Easy DIY Tool Organizer
Now you can fill your Easy DIY Tool Organizer with the tools you use the most in your crafting. Be sure to see the special file in the Free Resource Library with a list of Five Must-Have Cutter Crafting Tools which you likely have around your home already. This Easy DIY Tool Organizer will help you to organize those Must-Have cutter crafting tools.

Place your most used tools in the Easy DIY Tool Organizer
Decorate Your Easy DIY Tool Organizer
I used one of the large peony flowers that I made for my Lovely Peony Basket. You can decorate yours with any number of beautiful ornaments from your supplies.

My Easy DIY Tool Organizer on my desk.
Completed Project
Here is my finished Easy DIY Tool Organizer. I would love to see yours! What are you going to put in it?
Julie, cuttercrafter.com
Would you like to see some more of my FREE SVG projects? Check them out in my FREE Resource Library.
>> HOW TO ENTER THE FREE RESOURCE LIBRARY <<
This resource library is open to everyone for free. All you need is the password to get in, which you can get by filling out the form below.
If you already have your password, enter the resource library here.
