How to Use SVG Files with Scan N Cut
Learning how to use SVG files with Scan N Cut is important. Not all SVG files work well with Scan N Cut. In this tutorial you will learn how to make sure that your SVG file will work well with your Scan N Cut. ScanNCut SVG files need to be no larger than 11.75″ x 11.75″ using the standard sized mat, or 11.75″ x 23.75″ using the long mat. The DPI size also needs to be correct. Make sure that the ScanNCut SVG file has a minimum number of nodes. This tutorial will address all of these issues.

Scan N Cut
How was the SVG file Created?
SVG files may be created in any number of software programs. Some software allows the designer to add many different “pages” of file pieces on a single screen. This is fine if cutting from that software directly to a supported cutter. That software will allow you to select the specific portions of the designs to be cut in a given pass. SVG files of this type will work in many programs for many different cutters. However, any SVG file imported into the Brother Canvas Workspace software will be resized to fit the mat on the screen. When all pieces of the file are selected, and the width or length of the selection is greater than the screen mat size, the pieces will be resized to fit. So all of your design pieces may shrink to a very tiny size in the Brother Canvas Workspace or on the LED screen of your Scan N Cut.
FREE Rose SVG Cutting File
There is a Free Large 3D Rose cutting file in SVG format in my Free Resource Library for you to use as you work through this tutorial. When it is cut and assembled, this rose has a width of about 7″.
The cutting pieces for this project measure over 17.5″ wide when selected in their original size. The largest petals measure 3.45″ wide.

Original Size of Large Rose Cutting File – 17.5″ wide
But when you import this same design into Brother Canvas Workspace, you will receive a message that the design was resized to fit the Canvas Workspace.

Warning Message in Brother Canvas Workspace about Size
The resulting imported design in Brother Canvas Workspace was resized to be 11.75″ x 11.75″ and the largest petal measured 2.03″ wide. This size is about 58% smaller than the original. The final assembled flower would measure about 4.12″ wide. Now if this adjusted size is OK with you, then you can go ahead and cut the project to make the smaller rose.

Large Rose SVG file was resized in Canvas Workspace
Vendor Remedies for ScanNCut SVG Files
Some software vendors are aware of this issue, and save their larger SVG projects into multiple SVG files with a maximum width so that they will work with all software, including Scan N Cut. They will add all of the project SVG files to a single folder, and zip them up for a single download. You will need to unzip the folder once you have saved it to your computer, by clicking on the zipped folder, and selecting Extract All. Then you will be able to import one SVG file at a time to either Canvas Workspace or directly to your Scan N Cut via the Bluetooth connection, or via a thumb drive plugged in to the USB port on the machine.
How to Make Size Adjustments for ScanNCut SVG Files
If you have determined that you need to retain the sizing of the original file, how do you make the necessary size adjustments in the file so that it will work with the Scan N Cut? One option is to contact the original designer of the file, and ask them to limit the sizing of their SVG files to a width of 11.75″. However, that is not always practical for you or for the original designer. You can learn to make the necessary adjustments in the file so that it will work on your machine.
The best option is for you to use a third party software for making changes in your SVG file. Software that exports designs with the sizing of the original design are the free Inkscape , Make The Cut, or Sure Cuts A Lot (using the 96 DPI export option or Save as FCM). SCAL is the best option for MAC users.
The Large 3D Rose file is a good place for you to start. Select one of the above software programs to use for editing your SVG files. Plan to stick with it for all of your editing needs. You will need to learn how to use it for many different purposes. Each has its own learning curve. See my video tutorial covering use of each of these three programs for making the small changes that this file needs.
How to Reduce the Number of Nodes for a ScanNCut SVG File
Whenever you change file formats for a cutting file, it is possible that extra nodes will be added to the design. If a design has too many nodes, or construction points, it may not load into Canvas Workspace or the Scan N Cut. It is therefore important to reduce the number of nodes in the design before exporting as SVG. In Make the Cut, you can use Ctrl+Shift + X to view path detail.
Reducing the Node Count in Make The Cut

View Path Detail in Make The Cut
In this file there are only a total of 434 points, and 182 Nodes, as indicated on the top line of the window. This number of nodes is not a problem for Scan N Cut. Some files with lots of tiny detail can have upwards of 30,000 nodes. That would be too many. To reduce the number of nodes in Make The Cut, select all (Ctrl+A), Join (Ctrl+J), Auto Simplify Paths (Ctrl+Shift+Z). The number of nodes will be significantly lower if there are too many nodes.
Reduce the Node Count in Inkscape
If you are using Inkscape, and your SVG file has too many nodes, select all (Ctrl+A) and Simplify (Ctrl+L) as many times as needed to get rid of excess nodes, a few at a time. This file does not need it. You only need to reduce nodes or simplify paths if you get an error when trying to load your SVG file into Canvas Workspace or into the Scan N Cut machine.

Warning when attempting to transfer a design with too many nodes to Scan N Cut.
Reduce the Node Count Using Sure Cuts A Lot
To reduce the number of nodes in a file if you are using Sure Cuts A Lot, go to the Path menu at the top of the screen, and select Simplify. A window will open allowing you to see the nodes and reduce the number of nodes if there are too many. This design does not have too many nodes, so simplifying would actually add nodes as shown in the image below.

Use the Path Simplify tool to view the number and to reduce them if necessary.
Import your ScanNCut SVG Files into Scan N Cut Canvas Workspace or into the Machine
Once you have edited the SVG files to have its objects fit on a single design page in the software of your choice no wider than 11.75″, reduced the number of nodes if necessary, and exported the files as SVG for FCM using the proper DPI settings, then you are ready to transfer your files to your Scan N Cut machine for cutting. You can copy the files to a thumb drive, and plug them in to the machine’s USB port, or import them into Canvas Workspace to Transfer to your Scan N Cut.
Cut the pieces for your ScanNCut SVG Large 3D Rose, and you are ready to assemble your flower.

Large 3D Rose SVG Cutting File
You can get the FREE cutting file for this project as well as additional SVG projects in my FREE Resource Library.
>> HOW TO ENTER THE FREE RESOURCE LIBRARY <<
This resource library is open to everyone for free. All you need is the password to get in, which you can get by filling out the form below.
If you already have your password, enter the resource library here.
Thanks!
Julie
cuttercrafter.com